polymeric sealing coating
PartoSEAL is a polymeric sealing coating that consists of two components, including a dry powder component and an acrylic resin component, and requires only mixing to be used. The two components of this product, after combining with each other and adding some water, have excellent adhesion, and with their suitable paste properties, they make the operation of sealing sections very easy.
application
“PartoSEAL is used as a sealing product in places where we intend to insulate against water leakage. Including the following:
”
Insulation of roof gardens
Sealing elevator shafts
Insulation of ponds and water features
Sealing tunnels, dams and water tanks
Covering concrete water and sewage transmission lines
Sealing water pipes and ducts
Sealing pools and sewage septic tanks
Sealing and insulating the surfaces of water and wastewater treatment plants
Repairing elements with water leakage and dampness in bathrooms, basements and balconies
advantages
Anti-algae and moss
Resistant to frost process
Resistant to carbonation process
High adhesion to the surfaces under the work
Resistant to sunlight and UV rays
Impermeability and sealing in the section
No shrinkage and cracking after execution
Ease of use only by mixing except A and B.
Resistance to harmful chemical agents such as chlorides
Ability to seal and make the sections impermeable
Resistant to corrosive agents such as salts and chlorine ions
Resistance to alkalis and mild inorganic acids
Rapid adhesion to a variety of materials, especially concrete, brick and stone
packaging
This product is offered in two components:
Component A: 15 kg bucket liquid
Component B: in powder form in a 25 kg bag
Typical properties
Percentage of elongation more than 60%
Maximum thickness of each run hand ۱ mm
The thickness of the final layer ۱-۴ mm
tensile strength* ۲ MPA
drying time*
surface drying ۱.۵-۲ hours
final drying ۳-۷ days
* The mentioned data are obtained based on the latest controlled laboratory tests.
مشخصات فنی
درصد ازدیاد طول: بیش از ۶۰ درصد حداکثر ضخامت هر دست اجرا: ۱ میلیمتر ضخامت لایه نهایی: ۱ تا ۴ میلیمتر مقاومت کششی: ۲ MPA زمان خشک شدن: خشک شدن سطحی: ۱.۵تا۲ ساعت خشک شدن نهایی: ۳ تا ۷ روز داده های مذکور براساس آخرین تست های کنترل شده آزمایشگاهی حاصل شده است.
application guidline
۱. Do not apply a layer thicker than 1 mm in each hand.
۲. The thickness of the final layer should be between 1 to 4 mm depending on the water pressure and the type of use.
۳. Saturate the following sections with fresh water, but never have static water on the sections.
in the case of above situation, the useful life of the product is 12 months from the date of production.
mixing
All parts of the sealing operation must be saturated with fresh water and free of any contamination, grease, dust and static water. Gently pour the powder component into the liquid component. Turn on the mixer and continue the mixing process at low speed (less than 500 rpm) for 1 minute. Apply the prepared mortar on the surfaces with a trowel or spatula or brush. Treat the applied part with water for at least 1 day.
storage and shelf life
PartoSEAL is maintaned in closed packaging and away from direct rays of sun and ice situation.
in the case of above situation, the useful life of the product is 12 months from the date of production.
health and safety
there is not need for special actions but for observing safty actions, it is better to use protection gloves and eye glasses. In case of direct contact with skin or eyes, rinse immediately with water and see a doctor.
Please refer to the Safety Data Sheet (MSDS).
